L421 Four Post Lift Rack

L421 Four Post Lift Rack 14,000 Lb. Capacity, Split-Front for Easy Service Access.

L421 Specifications
Max. vehicle gross weight	14,000 lbs. (6350 kg)
Max. wheelbase	L421	w/ Extension
General Service:	188-1/2" (4788 mm)	226-1/2" (5753 mm)
2-wheel alignment:	172-1/2" (4382 mm)	210-1/2" (5347 mm)
4-wheel alignment:	158" (4013 mm)	196" (4978 mm)
Min. 4-wheel alignment	88" (2235 mm)	88" (2235 mm)
Max. lifting height	70" (1778 mm)	70" (1778 mm)
Alignment height	Any of 20 lock positions	Any of 20 lock positions
Minimum height	8-1/4" (203 mm)	8-1/4" (203 mm)
Overall height	93" (2362 mm)	93" (2362 mm)
Tread width
Min. inside:	40" (1016 mm)	40" (1016 mm)
Max. outside:	85" (2159 mm)	85" (2159 mm)
Motor	3 hp, 208-230 VAC, 60 Hz, 1 ph, 80-125 psi	3 hp, 208-230 VAC, 60 Hz, 1 ph, 80-125 psi
Air	80-125 psi	80-125 psi
Shipping Weight	4,600 lbs. (2087 kg)	+585 lbs. (+265 kg)

Models

L421		Four-Post Lift, Open Front

L421–43		L421 with (2) 8,000-lb. capacity Swing Air-Jacks

Standard Equipment

Two gusseted and louvered approach ramps
Two rear ramp stops
Two front wheel stops
Two wheel chocks
Two clip-on work steps with skid protection
Built-in, full-length jack rails
80” (2032 mm) flush-mounted rear slip plates with tethered lock pins
Built-in rub rails
Built-in turnplate pockets
Built-in air line kit
Pre-drilled for communications interface kit
Lubricator/air filter with auto-drain

Options

20–1587–1		L421 Runway Extension Kit with Filler Plates (not available on L424)

20–593–1		Communications Interface Kit (new rack)

20–1622–1		L421 and L424 Drive-Thru Kit*

20–1248–1		Wear Detector Plates

20–1365–1		Ramp Extension Kit (for low clearance vehicles)

25–140–1		Turnplate, 14” (356 mm), (2 required)**

25–129–1		Stainless Steel Turn Plate, 14” (356 mm), (2 required)***

46–372–1		Front Filler Plate (2 required)

64–50–2		Jack Pad (2 required)

133–62–1		8,000 lb. (3175 kg) Capacity Swing Air-Jack

20–1184–1		Front-Mount Power Unit Bracket

Drive-Thru Kit cannot be used on L421 with Extension Standard equipment with Hunter wheel alignment systems **Standard equipment with 811P-Plus Hunter Wheel Alignment Systems

click to enlarge

The Hunter L421 Lift has been certified under the program conducted by Automotive Lift Institute (ALI) and ETL Testing Laboratories, to comply with Safety Standard ANSI/ALI ALCTV-2006 and Electrical Standard ANSI/UL 201.

Because of continuing technological advancements, specifications, models and options are subject to change without notice.

NOTICE:

Product delivered to international markets may differ slightly in content to domestic product. Please consult your local distributor for details.

Ordering Information

For pricing and ordering information on Racks or other Hunter products, contact your local Hunter representative. See the representative locator or contact Hunter Engineering Company. To receive a quote on this equipment, go to Get-A-Quote.

^ Back to Top
Racks

WHAT'S NEXT?

TRANSLATIONS

L421 Four Post Lift Rack

Content on this page requires a newer version of Adobe Flash Player.

NOTICE: