HunterPro™ Automotive Kit:* 20-1661-3
The ultimate in setup rigidity, this set covers most
automotive rotors and drums in service today including
most odd configured rotors. Fits most hubless cast/composite
automotive rotors, drums and flywheels.
Kit includes:
A. Cone, Automotive Centering - 192-134-2
 1.84" – 2.20"
B. Cone, Automotive Centering - 192-135-2
2.12" – 2.47"
C. Cone, Automotive Centering - 192-136-2
2.37" – 2.75"
D. Cone, Automotive Centering - 192-137-2
2.65" – 3.00"
E. Cone, Automotive Centering - 192-138-2
2.92" – 3.30"
|
|
F. Cone, Reversible Centering - 192-133-2
2.00" – 3.98"
G. Flange Plate - 51-1892-2
4.80"
H. Flange Plate - 51-1893-2
Automotive Composite,
5.43"
I. Flange Spring, - 98-383-2
1.92" x 1.00"
|
| |
|
|
HunterPro Light Truck Kit:* 20-1662-3
This set covers most light trucks up to 3/4 ton. Fits most
hubless cast/composite light truck rotors, drums and
flywheels. The 20-1662-3 set compliments the 20-1661-3
and must be used together.
Kit includes:
A. Cone, Lt. Truck Centering - 192-139-2
3.20" – 3.57"
B. Cone, Lt. Truck Centering - 192-140-2
3.47" – 3.85"
C. Flange Plate - 51-1894-2
Lt. Truck Composite, 7.25"
|
|
|
| |
|
|
HunterPro Larger Light Truck Kit:* 20-1663-3
This set covers most larger light trucks up to and including
1-ton and super-duty trucks. Fits most hubless
cast/composite light truck rotors, drums and flywheels.
Kit includes:
A. Cone, Lt. Truck Centering - 192-141-2
3.75" – 4.12"
B. Cone, Lt. Truck Centering - 192-142-2
4.03" – 4.40"
C. Cone, Lt. Truck Centering - 192-143-2
4.30" – 4.67"
D. Cone, Lt. Truck Centering - 192-144-2
4.57" – 4.95"
E. Cone, Lt. Truck Centering - 192-145-2
4.85" – 5.22"
F. Cone, Lt. Truck Centering - 192-146-2
5.12" – 5.50"
|
|
G. Cone, Lt. Truck Centering - 192-166-2
5.40” – 5.75"
H. Flange Plate - 51-1895-2
Large Lt. Truck, 7.25"
I. Flange Plate - 51-1896-2
Large Lt. Truck, 6.50"
J. Flange Spring - 98-383-2
1.92" x 1.00" |
| |
|
|
HunterPro F-150 Adaptor:** 20-2109-3
Addresses the 2004 and up Ford F-150 two-wheel-drive
6- and 7-lug front rotors with internal bearings, which are
extremely difficult to setup and machine accurately with
traditional brake lathe adaptors.
Kit includes:
A. Ford F-150 Flange Plate - 51-2184-2
B. Bearing Support Flange - 51-2185-2
|
|
|
| |
|
|
HunterPro Rotor Adaptor:* 20-1664-3
For hubless cast/composite auto and light truck rotors. Covers
90% of rotors in service today. Designed as an entry level or
second adaptor set used in busy shops. Fits rotors with hub
bore 1.85" - 3.75".
- Provides accurate mounting of cast and composite hubless rotors with only two adaptors.
- Captured mounting cone and spacer speeds setup.
Ideal for high-volume shops.
Kit includes:
A. Captured Cone and Flange Spacer - 184-62-2
B. Flange Spacer - 184-63-2 |
|
 |
| |
|
|
QuickChuck™ Adaptor Kit: 20-1273-1
Three-jaw chuck adaptor for hubless drums and rotors with
center holes from 2.13" to 4.25" can obsolete all other adaptors
for use with hubless drums. It offers the advantage of
unparalleled centering ability combined with speed of setup.
Kit includes:
A. Three-Jaw Chuck Adaptor - 175-198-2
without Jaws
B. Jaws Set, Standard Size - 20-1316-2
2.13"- 4.25"
(shown installed in Three-Jaw
Chuck)
C. Backing Plate, Medium, 5.13" - 175-199-2
D. Tool, T-Wrench, Three-Jaw Chuck - 221-590-2 |
|
 |
| |
|
|
Truck Jaw Kit: 20-1274-2
Truck Jaws for 20-1273-1 for use in mounting hubless
drums and rotors with center holes from 3.63" to 5.75".
Must be ordered as a numbered set. |
|
 |
| |
|
|
Extra-Large Cup and Cone Kit: 20-1378-1
For 1" Arbors.
Kit includes:
A. Cone, 3.88" – 4.44" - 192-118-2
B. Cone, 4.13" – 4.97" - 192-119-2
C. Cone, 4.83" – 5.50" - 192-120-2
D. Cup, Extra Large, 7.25" - 175-192-2
E. Cup, Extra Large, 6.25" - 175-251-2 |
|
 |
| |
|
|
Hubbed 2WD/4WD Rotor Adaptor: 20-1424-1
’92-current 3/4- to 1-ton GM 4WD, ’94-current 3/4-
to 1-ton Dodge 2WD and 4WD; includes Small Cone, 192-116-2 (not shown). |
|
 |
| |
|
|
Pilotless Drum Adaptor Kit: 175-255-1
For mounting drums without pilot holes, such as VW and
Subaru. Requires 97-431-2 for BL505 or 97-405-2 for early
BL500 models. |
|
 |
| |
|
|
Self-Centering Spacer:
46-432-2
Compensates for overtightening
arbor nut and
some mounting errors
encountered during setups. |
|
Deep 1-Ton Drum
Adaptor: 175-236-1
Required when turning drums
in which the friction surface
is wider than 3.75". |
| |
|
|
Extra-Small Drum
Adaptor: 175-250-1
For drums smaller than 7"
diameter. Includes negative
rake insert (221-583-2). |
|
Taper Adaptor: 97-431-2
Required to mount flywheel
kit, 20-1407-1 and pilotless
drum kit, 175-255-1. Order
97-405-2 for BL500 models
only. |
| |
|
|
Bushings Reducer Kit:
20-1333-1
Required when using
1-7/8" adaptors on 1"
arbors. Set of three 113-
213-2 adaptors. |
|
Flywheel Adaptor Kit: 20-1407-1
Mounts flywheels with a pilot hole smaller than 1".
Includes:
A. Flywheel Cone - 175-247-2
B. Flywheel Base - 175-253-2
Requires 97-431-2 for BL505 or
97-405-2 for BL500 models only. |
| |
|
|
Extra-Small Cup:
175-249-2
Cup, 3.50" |
|
Extra-Small Cone:
192-116-2
Cone, 1.31" to 1.75" |
| |
|
|
1" Arbor x 9.3": 97-422-2
For the BL505/501 Series Lathes
1" Arbor x 9.3": 97-394-2
For use with BL500 model only (not shown). |
|
|
1-7/8" Arbor Kits
|
Hubbed Heavy-Duty Truck Adaptor Set: 20-1396-2
For mounting heavy-duty hubbed rotors and rums with
center holes from 2.16" to 6.00". Cones can also be used
for hubless rotors and drums with clamp cups 175-220-2,
175-219-2 and spring 98-344-2. 20-1490-1 or 20-1271-1
1-7/8" Arbor Kit required.
Kit includes:
A. Cone, 2.16" – 3.37" - 192-100-2
B. Cone, 2.25" – 3.62" - 192-121-2
C. Cone, 3.60" – 4.50" (2 ea.) - 192-122-2
D. Cone, 3.50" – 4.87" (2 ea.) - 192-123-2
E. Cone, 4.62" – 6.00" (2 ea.) - 192-124-2 |
|
 |
Hubless Medium-Duty Truck Adaptor Set: 20-1397-2
Use for mounting hubless medium-duty items with center
holes from 3.83" to 5.00". 20-1490-1 or 20-1271-1, 1-7/8"
Arbor Kit required.
Kit includes:
A. Cone, 3.82" – 4.42" - 192-125-2
B. Cone, 4.35" – 5.00" - 192-126-2
C. Clamp Cup, 6.25" (set of 2) - 175-220-2
D. Spring - 98-344-2 |
|
 |
| |
|
|
Hubless Heavy-Duty Truck Adaptor Set: 20-1398-2
For mounting hubless heavy-duty components with center
holes from 4.88" to 8.25". 20-1490-1 or 20-1271-1,
1-7/8"
Arbor Kit required.
Kit includes:
A. Cone, 4.88" – 5.50" - 192-105-2
B. Cone, 5.44" – 6.03" - 192-106-2
C. Cone, 5.97" – 6.50" - 192-107-2
D. Cone, 6.50" – 7.44" - 192-127-2
E. Cone, 7.00" – 7.64" - 192-109-2
F. Cone, 7.58" – 8.17" - 192-110-2
G. Clamp Cup, 7.25" (2 ea.) - 175-354-2
H. Clamp Cup, 9.25" (2 ea.) - 175-219-2
I. Spring - 98-344-2 |
|
 |
| |
|
|
1-7/8" Arbor Kit: 20-1490-1
1-7⁄ 8" HD Arbor Kit for the BL505/501.
Kit includes:
A. Arbor, 1-7/8" x 17" - 97-420-2
B. Tool, Spanner Wrench - 221-584-2
C. Nut, 1-7⁄ 8" Arbor - 76-342-2
D. Spacer, 2" - 46-448-2
E. Spacer, 3" (2 required) - 46-449-2
1-7/8" Arbor Kit: 20-1271-1
Same as 20-1490-1, except the arbor (97-404-2) has a smaller taper for the BL500 model (not shown). |
|
 |
11/16" Arbor Kit
11/16" Arbor Kit: 20-1489-1
11/16" Arbor Kit for mounting splined, hubbed rotors
without having to remove the sealed bearings (BL505).
Kit includes:
A. Cone, 0.70" to 1.70" - 192-115-2
B. Spacer, .75" (2 ea.) - 46-446-2
C. Spacer, 1.50" - 46-447-2
D. Nut, Arbor 11/16" - 76-341-2
E. Arbor, 11/16" – 7.13" - 97-432-2
Arbor Kit: 20-1272-1
Same as 20-1489-1 except the arbor (97-400-2)
has a smaller taper for the BL500 model (not shown). |
|
 |
|
* Patented
** Patent Pending
|
