|
|
Add Full-Service Capability to Existing Single-Post and Twin-Post Lifts
|
The Hunter Multi-Service Lift turns an existing single-post or side-by-side twin-post [57-1/2”, (1461 mm) center-to-center] lift into a full-service lift and alignment rack. It also fits most two-post above-ground lifts.
- Designed for four-wheel alignment capability, including rear wheel slip plates, leveling legs, built-in turnplate pockets.
- Single-post and twin-post models have 8,000-lb. (3629 kg) capacity to handle virtually all passenger cars and light trucks.
NOTICE:
Product delivered to international markets may differ slightly in content to domestic product. Please consult your local distributor for details.
|
|
 |
|
| Model |
Standard
Length |
Extended Length |
| Max. vehicle gross weight |
| Single Post |
8,000 lb. (3629 kg) |
| Twin Post |
8,000 lb. (3629 kg) |
| Max. wheelbase |
| General service |
152” (3861 mm) |
174” (4420 mm) |
| 2-wheel alignment |
139” (3531 mm) |
161” (4089 mm) |
| 4-wheel alignment |
138” (3505 mm) |
138” (3505 mm) |
| Min. 4-wheel alignment |
88” (2235 mm) |
| Alignment height |
36” (914 mm) |
| Standard (except D1-M is 30” standard) also available in 24” (610 mm). All models available in optional 30” (762 mm) or 24” (610 mm) |
| Tread width |
| Min. inside |
40” (1016 mm) |
| Max. outside |
79” (2007 mm) |
| Shipping weight (without jacks) |
| D1 |
2400 lbs. (1089 kg) |
2600 lbs. (1179 kg) |
| D2 |
2400 lbs. (1089 kg) |
2500 lbs. (1134 kg) |
- Two standard-length, 36” (914 mm) approach ramps
- Four leveling legs, 36” (914 mm), (except D1-L, 30”)
- Two rear ramp stops
- Two wheel chocks
- Four down-position leveling screws
- Two retractable work steps with skid protection
- Built-in formed rub rails
- Built-in full-length jack rails
- 59” (1499 mm) rear slip plates, flush mounted with tethered lock pins
- Floor protectors for leveling legs and leveling screws
- Mounting hardware kit
- Built-in turnplate pockets
- Pre-drilled for communications interface kit
- Pre-drilled for air line kit
- 20-593-1 Communications Interface Kit
- 20-996-1 Air Line Kit
- 25-140-1 Turnplate, 14” (356 mm) (2 required)*
- 25-129-1 Stainless Steel Turnplates (2 required)*
- 46-372-1 Front Filler Plate, (2 required)
- 20-1403-1 Jack Riser Kit
- 133-35-1 Swing Air Jack Assembly
- 133-63-1 Air-Actuated Power Jack Assembly
- 147-44-1 Optional short 24” (610 mm) approach ramps (2 required)
- 20-1249-1 Wear Detector Plates
- 213-47-2 Drive-On Mirror
*Available with Hunter wheel alignment systems
- D1-M Standard Length Single-Post Rack
- D2-M Standard Length Twin-Post Rack
- D1-L Extended Length Single-Post Rack
- D2-L Extended Length Twin-Post Rack
- 209-43 D1-M with (2) Swing Air Jacks
- 209-59 D2-M with (2) Swing Air Jacks
- 209-70 D2-M with (2) Air-Actuated Power Jacks
- 209-71 D1-M with (2) Air-Actuated Power Jacks
- -L** Add to model number for Extended Length Rack (i.e. 209-70-L)**
- -DT** Add to model number for drive-thru capability
** Available at extra cost; see form 700D-SYS.
See the recommended configuration.
Because of continuing technological advances, specifications, models and options are subject to change without notice.
Ordering Information
|
|
|
